Call:- 01670-070357 to repair your industrial electronics items.

Mitsubishi FX3U ENET Communication Module

Availability:

Out of stock


Brand:  Mitsubishi
Model:  FX3U ENET
Specification: Ethernet Communication Module 10/100baset, TCP/Ip, Udp, Pop3, MODBUS TCP
Condition: Used/Refurbished
Origin: JAPAN
Warranty: Three months.
Download Manual
Show Other Products
Call us at +88 01670070357

Call for Repair

FX3U ENET Mitsubishi Communication Module

Ethernet Communication Module 10/100baset, TCP/Ip, Udp, Pop3, MODBUS TCP

Product Details

Mitsubishi FX3U ENET Network communication modules for use with FX3U PLCs. These special function modules fit on to the right hand side of the base units and occupy 8 I/O points. The FX3U-ENET communications module provides the FX3U with direct connection on to an Ethernet network With this module FX3U PLCs can exchange data quickly and easily with SCADA systems in addition to supporting program up/down load and monitoring.

Two network communication modules for use with FX3U PLCs. These special function modules fit on to the right hand side of the base units and occupy 8 I/O points

The FX3U-64DP-M is a Profibus master module that allows you to integrate an FX3U PLC system as a class 1 master of a Profibus/DP network
This module provides comprehensive data and alarm processing to the Profibus/DP V1 standard and is easily setup with the GX Configurator DP software
The FX3U-ENET communications module provides the FX3U with direct connection on to an Ethernet network
With this module FX3U PLCs can exchange data quickly and easily with SCADA systems in addition to supporting program up/down load and monitoring
The module also supports peer-to-peer connection to other FX3U and Q Series PLC’s

  • Manufacturer: Mitsubishi Electric
  • Ethernet interface block FX3U-ENET-ADP
  • Transmission Specifications Data transmission speed: 100Mbps or 10Mbps,
  • Communication mode: Full / half duplex
  • Transmission method: Baseband
  • The maximum segment length: 100m
  • The maximum number of nodes / connection: 10BASE-T: cascade up to four stages
    100BASE-TX: cascade up to two-stage
    above is the connection possible number of stages at the time of use repeater hub.
    Can be connected to the number of stages at the time of switching hub used, please check with the manufacturer of the switching hub to be used.
  • Connector: RJ45
  • function: · MELSOFT connection
    communicate by · MC protocol
    direct connection with · MELSOFT (simple connection)
    and connection CPU search function and time setting function
    ? time setting function (SNTP client), executable only after the establishment of the trigger conditions
    diagnosis from · MELSOFT function
    data monitoring function
  • Number of connections: MELSOFT connection + MC protocol + data monitoring ? 4 connection
  • It can be connected to the number of the basic unit: One
    Ethernet adapter, as well as the communication function expansion board and other communication special adapter, and 1 channel the communication channel (CH) occupation.
  • Apply PLC: FX3S, FX3G (V2.00 or later), FX3U (since V3.10), FX3GC (V2.00 or later), FX3UC (V3.10 or later)
    connection to the FX3S is required FX3S-CNV-ADP.
    Connection to the FX3G is required FX3G-CNV-ADP.
    FX3U, connection to the FX3UC-32MT-LT (-2), you must have the function expansion board.
  • mass: 0.1kg
  • Power Specifications:
  • Power supply: 30mA / DC5V (internal power supply from DC5V power of the basic unit)
  • Allowable momentary power failure time: As well as the sequencer to be connected
  • Ambient temperature: 0 ~ 55 °C ····· operation, -25 ~ 75 °C ····· during storage
  • Relative humidity: 5 ~ 95% RH (non-condensing) …… operation
  • Vibration resistance When the DIN rail mounting Frequency: 10 ~ 57Hz: Half amplitude: 0.035mm X, Y, Z each direction 10 times (for a total of each 80 minutes)
  • Frequency: 57 ~ 150Hz: Acceleration: 4.9m / s2 X, Y, Z each direction 10 times (for a total of each 80 minutes)
  • Direct mounting at the time Frequency: 10 ~ 57Hz: Half amplitude: 0.075mm X, Y, Z each direction 10 times (for a total of each 80 minutes)
  • Frequency: 57 ~ 150Hz: Acceleration: 9.8m / s2 X, Y, Z each direction 10 times (for a total of each 80 minutes)
  • Impact resistance: 147m / s2, duration of action 11ms, X at half-sine pulse, Y, Z directions 3 times each
  • Anti-noise: Noise voltage 1,000Vp-p, noise width 1μs, due to rising 1ns, cycle 30 ~ 100Hz of noise simulator
  • Withstand voltage: All terminals and between the ground terminal: AC500V 1 minute
  • Insulation resistance: All terminals and between the ground terminal: DC500V 5MΩ more in insulation resistance tester
  • Working environment: Corrosive, there is no flammable gas, conductive dust (dust) that is not terribly
  • Use advanced: 2000m or less
    can not be used in the pressurized environment to more than atmospheric pressure. There is a possibility of failure.

Specifications

Attribute Value
Manufacturer Series FX3U Series
For Use With FX3U Series
Number of I/O 8
Voltage Category 24 V dc
Module Type Ethernet Communications Module
Length 90mm
Width 55mm
Depth 87mm
Dimensions 90 x 55 x 87 mm
SKU: 5221 Category:
Call Now Button